Fischer Mechanical 636-327-4238
Get an estimate

Tell us the building, the work and your timeline. Estimates are free.

Blog / HVAC installation

What is a VAV system? Variable air volume explained for building owners

Fischer Mechanical, November 17, 2026

A VAV (variable air volume) system heats and cools a building by keeping the supply air at a steady temperature and changing how much of it goes to each room. A room that needs more cooling gets more air. A room that needs less gets less. It's a common choice for offices, schools and other multi-zone buildings, and most of its problems come from controls, not equipment.

How a VAV system works

A VAV system has three main parts:

  1. The air handler. A central unit, on the roof or in a mechanical room, that filters the air, mixes in outdoor air, cools it (and sometimes heats it) and pushes it into the ductwork. Its supply fan speeds up and slows down as the building's demand changes.
  2. VAV boxes. Each zone has a terminal box in the ductwork with a damper that opens and closes to change the airflow into that zone. Many boxes also have a reheat coil, hot water or electric, for zones that need heat or need less cooling than the minimum airflow would deliver. Some boxes also have their own small fan.
  3. Controls. A thermostat or sensor in each zone tells its box what to do, and the building automation system ties the boxes and the air handler together.

That's how a 2001 Department of Energy study of commercial HVAC describes it: airflow to the space is modulated by a terminal box with a valve, and the box may include a reheat coil and its own fan (DOE, Energy Consumption Characteristics of Commercial Building HVAC Systems).

VAV vs. constant volume

The older approach is constant air volume (CAV). The fan runs at one speed, every zone gets the same airflow all the time, and temperature is controlled by reheating cold air. That means cooling air and then heating it back up, even on mild days. The same DOE study notes that CAV doesn't reduce airflow and depends on reheat to control the cooling delivered, and that energy codes often don't allow it.

VAV cuts that waste in two ways. When the building needs less cooling, the fan slows down and uses less power. And because zones get less air when they need less cooling, there's less cold air to reheat.

Where VAV fits

VAV works best in buildings with many zones that need different things at the same time:

  • Offices, where a sunny corner office, an interior conference room and an open floor all have different loads.
  • Schools, where a full classroom, an empty classroom and a gym can sit off the same air handler.
  • Medical offices, labs and government buildings with varied rooms and long operating hours.

For a small building with one or two zones, packaged rooftop units or split systems are usually simpler. For large single spaces like a sanctuary or an arena, a dedicated unit sized for that space often makes more sense than VAV boxes.

Common VAV problems

When building owners call about a VAV system, the complaint is usually comfort: some rooms too cold, some too hot, or the system running hard when the building is half empty. The causes we see most often:

  • Failed actuators and stuck dampers. A box damper that won't move gives its zone the same airflow no matter what the thermostat asks for.
  • Bad airflow sensors. A dirty or failed sensor tells the controller the wrong airflow, so the box over- or under-delivers.
  • Reheat valves that leak or stick. Hot water leaking through a valve can heat a zone while the system is trying to cool it.
  • Minimum airflow set too high. If boxes never close down below a high minimum, rooms get overcooled and the reheat has to make up for it. That's paying twice.
  • Duct static pressure set too high. The supply fan works harder than it needs to, and boxes can whistle or be hard to control.
  • Controls overridden over the years. Schedules turned off, setpoints locked, boxes left in manual. Each fix made sense at the time, and together they can undo the system's efficiency.

Controls are a big enough issue that ASHRAE wrote a guideline for them. ASHRAE Guideline 36 provides standard high-performance control sequences, starting with VAV air handlers and terminal units in its first version. ASHRAE notes that custom sequences are often simplified to keep things simple, often fail to meet ASHRAE's energy and ventilation standards, and are often poorly programmed and commissioned. A 2021 update added automatic, dynamic calculation of VAV box minimum airflow setpoints, and ASHRAE reported early projects using the guideline cut boiler energy by more than half in two buildings while keeping code-minimum ventilation.

Retrofit options

If your VAV system is underperforming or aging, you rarely have to start over. The ductwork and many of the boxes can often stay. Options, roughly from smallest to largest:

  1. Recommission what you have. Test each box, repair actuators and sensors, fix leaking reheat valves, and reset minimums and static pressure. It's often one of the least expensive ways to improve comfort and cut energy use.
  2. Upgrade the controls. Replace old box controllers and program modern sequences, such as those in Guideline 36, so the air handler and boxes work together.
  3. Replace boxes selectively. Swap out boxes that are failing or badly sized, especially in zones that have been renovated.
  4. Replace the air handler. A new unit with variable-speed fans and better coils can keep the existing duct and box layout.
  5. Change the heating and cooling source. The boxes and air handler don't care where their hot and chilled water come from, which opens the door to other plant options.

VAV and geothermal

That last option is where geothermal can come in. A central water-to-water heat pump connected to a ground loop can produce the hot and chilled water that feeds an existing air handler and its VAV boxes, so a building can keep much of its distribution system.

There is one thing to check. Boilers usually make hotter water than heat pumps. The Department of Energy's guidance on electrifying large buildings with boilers says water in the range of 120 to 150°F can often heat a building in place of 180°F, recommends lowering hot water temperature in steps and testing comfort, and notes that lower temperatures may require changes to the VAV boxes or fan coils at the end of the system. The same guidance lists keeping existing pumps, VAV boxes and controls in place as a way to cut project cost. A design review tells you which reheat coils can work at lower temperatures and which need to be replaced.

If the air handlers are rooftop units nearing the end of their life, it's also worth reading our guide on when to replace rooftop units before you decide. Pairing the replacement with a change in plant can cost less than doing them years apart.

Next step

Whether you need a VAV system for a new building, replacement boxes or air handlers, or a look at replacing the plant behind them, we install VAV, chilled water and heat pump systems for St. Louis-area schools, offices and public buildings. Request a free estimate or call 636-327-4238. To compare geothermal against a conventional replacement, try the geothermal calculator.

Call 636-327-4238Email us